#Massey ferguson to 35 hyd. pump valve manual#
#Massey ferguson to 35 hyd. pump valve full#

It always worked perfectly until we fitted the approx 400 lb 3 ph lifted cutter. Do you have any idea why the position of the rear arms can influence things at the front end? Just like Pete from the UP mine has a two way valve to pick whether the stuff at the front or the back gets the fluid flow. In one direction, the backhoe is used (believe the 3 point is disabled-never used it) and the other direction, the loader operates. My hoe operates slowly and won't move two cylinders simultaneously. It sometimes takes 10-20 seconds for the loader to respond after startup. The pump does not have allot of flow capacity. My MF135 is equipped with a backhoe and loader. Not sure the draft setting comes into play on this. Try raising the arms fully and then see if the FEL works. Some Masseys require the 3 pth to be fully raised to use other hyd. I'll look at filters but am still a bit mystified. The MF135 is a bit simpler than the Ford as it only has the one pump. I will check the loader again(though it's such a simple one that I doubt it can have much to hide!). Although I don't see how filters would affect one end and not the other (my ignorance) I'll give them a shot and let you know. As I understand it the 135 has only the one pump and that does seem to work fine at the rear. The cutter bar uses the PTO rather than hydraulics so that won't have drawn any. The fluid level was above the low line but I've topped it up to full. Thanks Joel,(sorry for the delay -been away), So I'd stop using the machine, and inspect the loader frame for a 'reservoir' and a filler plug that looks out of place comapred to seeing it on a tank or reservoir. The pump for the loader is located on the front of the engine under the radiator. The loader uses the framework (tubing) of the loader itself as a reservoir. In addition, if it is fluid-level related you will likely ruin the pump for the loader which is probably separate from the 3-pth pump, but they may use the same fluid reservoir-but not always my buddy has a 1969 Ford 2000 with a factory loader. Let me know what you find after checking your fluid levels and filters. I'm not familiar with your particular tractor, but I'm willing to bet that your problem is very simple in nature. Have you checked and/or changed your filters recently? Do you have any idea when they were changed last? It's possible that your filter is plugged up, causing you to lose fluid flow to your pump.Д«oth of these problems usually take place right after hooking up an implement that is powered by hydraulics. The mower's hydraulic circuit could have been completely dry, which could have sucked any reserve you had from your tractor when it filled. When you installed the mower on the back, it's possible that you lost just enough fluid to cause this problem. Have you checked your hydraulic fluid levels? The most common problem is that you don't have enough fluid to operate/extend the cylinders. I'm sure somebody here will be able to help you solve this problem.Д«eing that you are new to tractors, I would like to go over some of the basic stuff with you. I'm a newcomer to tractors and will gratefully receive any ideas that experienced users/owners may have.

#Massey ferguson to 35 hyd. pump valve full#

We recently fixed a finger bar grass cutter to the machine and found that the front loader refused to respond to requests to raise itself! Told by various experts that an inability of the rear arms to move freely through their full scope would disable the front loader I removed the fingerbar - but the front still won't work! The rear arms will happily go up and down all day. Massey Ferguson 35 Specifications General SpecificationsДҐ2.6 liters (13.9 US gal.

#Massey ferguson to 35 hyd. pump valve manual#

The MF 35 is equipped with manual steering, independent manual shoe/drum brakes, open operator station and 52.6 liters (13.9 US gal. The cylinder bore is 84.0 mm (3.31 in) and the piston stroke is 98.0 mm (3.86 in). in) four-cylinder natural aspirated gasoline engine.This gasoline engine was available after 1961. in) three-cylinder natural aspirated diesel engine with 91.0 mm (3.58 in) of the cylinder bore and 127.0 mm (5 in) of the piston stroke.The tractor could be equipped with the following engines: The MF 35 is equipped with one of two engines: a 2.5 L three-cylinder diesel engine or a 2.2 L four-cylinder gasoline engine and one of two transmissions: gear type transmission with dry disc clutch and 6 forward and 2 reverse gears or partial power shift transmission with 12 forward and 4 reverse gears. The Massey Ferguson 35 is a 2WD utility tractor manufactured by the Massey Ferguson in Detroit, Michigan, USA from 1960 to 1965.

Massey ferguson to-35 hyd. pump valve